select / radio button - radioselection

[klabautermann]

as I select right?

so far I have everything installed first and copy and delete the version made in retrospect!

I would like now but in the beginning the so select only installed what is needed to the particular version!

for example:
%appfolder%\ program name \ version (a) \ data \ ...
%Appfolder% \ program name \ version (b) \ data \ ....
&appfolder% \ program name \ version (c) \ data \ ....

radio button (12 buttons):
there is a radioselction (session variable) for version (a / b / c) and drive (C / D / E / F)

translated by google translator

[Worti]

translated back by Google.

Im not sure what you want / Ich bin mir nicht sicher was du möchtest.

Check the Custom Screen On Preload and On Ctrl Message / Prüfe den Custom Screen bei On Preload und on Ctrl Message.

radio.suf

Regards / Gruss

[klabautermann]

hello,
I 'm not sure if I have expressed myself properly !

I want to offer different versions in a setup 5-6 for the drive c / d / e / f where after the selection- only files, folders ect to install a version !

on the one hand are the files, folders ect. but partly identical have different paths !

so far I 've always just installed everything and created after the installtion the commands to copy or delete the individual paths what I want now done in advance!


radio button ( radioselection1 )
- Germany * > radioselection2
- International **> radioselection3

* radiobutton ( radioselection2 )
- Version a ( germany ) ***> radioselection4
- Version b ( germany ) ****
- Version c ( germany ) *****

radiobutton ** ( radioselection3 )
- Version b ( international) ****** > radioselection5
- Version c ( Interntaional ) *******

*** radiobutton ( radioselction4 )
CTRL_RADIO_BUTTON_01 = C:
CTRL_RADIO_BUTTON_02 = D:
CTRL_RADIO_BUTTON_03 = E:
CTRL_RADIO_BUTTON_04 = F :

****** radio button ( radioselection7 )
CTRL_RADIO_BUTTON_13 = C:
CTRL_RADIO_BUTTON_14 = D:
CTRL_RADIO_BUTTON_15 = E:
CTRL_RADIO_BUTTON_16 = F :

ongoing

perhaps it's even easier than I think or do it too complicated because I think wrong!

My thought was the selection- to put before the file !

state is :
appfolder % % \ program name \ version ( a) \ data \ ...
Appfolder % % \ program name \ version ( b ) \ data \ ....
& appfolder % \ program name \ version ( c ) \ data \ ....

my thought / should state :

CTRL_RADIO_BUTTON_01 % % \% % appfolder \ program name \ version ( a) \ data \ ...
CTRL_RADIO_BUTTON_05 % % \% % appfolder program name \ version ( b ) \ data \ ....
CTRL_RADIO_BUTTON_09 % % \% % appfolder program name \ version ( c ) \ data \ ....

note:
% appfolder % = drive c / d / e / f

have at the moment a blackout

[klabautermann]

up`s,

CTRL_RADIO_BUTTON_01 % \ program name \ version ( a) \ data \ ...
CTRL_RADIO_BUTTON_05 % \ program name \ version ( b ) \ data \ ....
CTRL_RADIO_BUTTON_09 % \ program name \ version ( c ) \ data \ ....

[klabautermann]

as you have to without the other files / folders to be installed, proceed to a file / folder to assign a version!

* RadioSelectionGerElsa25
when clicked radio button _01 will then file ** "a" install
when clicked radio button _02 will then file ** "a" install
when clicked radio button _03 will then file ** "a" install
when clicked radio button _04 will then file ** "a" install

* RadioSelectionGerElsa37
when clicked radio button is _05 file ** "b" then install
when clicked radio button is _06 file ** "b" then install
when clicked radio button is _07 file ** "b" then install
when clicked radio button is _08 file ** "b" then install

01.05 .... = C: \
02.06 .... = D: \
03.07 .... = E: \
04,08, .... = F: \

* version
File or folder ** and